Yz 125 fork seals

Yz 125 fork seals DEFAULT

Leaky fork seals may be seem like minor problem, but it can lead to further damage of your fork internals, and even handling and braking safety. In this guide, we go through each step you need to know to replace oil and dust seals in your bike.

Whether you’re out with friends or at the track on race day, leaky seals can ruin any day of riding, especially if that blown seal is on the brake side. When your forks seals are just leaking or won’t hold hardly any oil at all, your forks won’t dampen or rebound the way they’re intended to. The oil helps create bottoming resistance, allowing the fork to stay up in the stroke where it is intended to perform.

Most current generation forks contain a closed cartridge, which houses the damping and rebound valving as well as oil. The outer chamber houses the fork spring plus additional oil. When the forks main seals blow, it’s the oil in the outer chamber that leaks out.

As oil seeps out through the seal and down the lower fork leg, dirt and debris can stick to the tube. The initial size of the tear in the seal may be small and somewhat unnoticeable, but after dirt makes its way past the dust wiper, it damages the seal itself, causing oil to leak out more rapidly.

Unaddressed leaking fork seals can lead to dirt working its way through the fork internals, likely leading to more damage and potentially costly repairs.

Replacing fork seals is something that can generally be done in a well-equipped garage with the help of some standard tools and supplies, plus a couple specialty tools that are readily available.

It’s important to note that different suspension manufacturers have different methods of disassembly and reassembly, so always be sure to reference your owner’s manual for guidance specific to your application. This guide is intended to be a general how-to and not all steps will be the same across all applications.

In this step-by-step guide, we replaced the fork seals on a set of used Showa closed cartridge forks off a 2007 Honda CRF 450R. For the purpose of this guide, we will focus on a simple seal replacement to get you back on the track or trail rather than a full cleaning of the outer chamber and seal replacement.

The first step before you begin your repair is ensuring you have the correct tools in your arsenal, and a set of new seals to install. Trying to “MacGyver” things with the incorrect tools can easily result in more repairs and more cost to you. Below is a list of tools we used for this project:

  • 47mm ProX fork seal kit
  • Torque wrench (recommended from a reputable company for accuracy)
  • Socket wrench (3/8 drive)
  • 8mm socket or 8mm T-handle wrench
  • 10mm socket or 10mm T-handle wrench
  • 17mm, 19mm, 21mm sockets
  • 17mm open end wrench
  • 5mm Allen wrench
  • Fork cap wrench
  • #2 flat head screw driver
  • 47mm fork seal bullet
  • 48mm fork seal driver
  • Seal and O-ring grease
  • 5W fork fluid (or whatever is recommended in your manual)
  • Pen and paper
  • 600 grit wet/dry sand paper
  • Work bench vise with rubber padded jaws
  • Oil drain pan
  • Suspension-specific cleaning chemical (ex: Maxima Suspension Clean)
  • Awesome Orange (diluted with water 50/50 mixture)
  • Microfiber towels

**NOTE:Tool sizes may vary depending on the suspension’s manufacture.

There are many choices when sourcing new seals. OEMs are great, but can be overpriced. ProX oil seals and dust seals are made by the same OE suppliers in Japan to meet OEM quality without the price tag. They are available both individually and as sets.

To start, it is always a good idea to have all your tools laid out on a clean work bench or table. Start by placing your bike on a stand and removing your front wheel, then your forks. Be sure to remove the fork guards and brake caliper (when applicable) before loosening the triple clamps and removing the forks completely.

Check your rebound clicker settings using a flat head screwdriver and write them down. To do this, turn the clicker clockwise, counting each notch you feel until it stops. Once it stops, do not force it. The number of clicks is your setting. You will need to reset to this after reassembling your fork.

Now, with the clicker settings recorded and the fork(s) completely removed from the bike, we can begin the seal replacement process.

  1. Place the fork in the vise by clamping it by the axle lug.

    prox-fork-seal-replacement-32
  2. Using a socket/wrench, fully loosen the bottom bolt underneath the axle lug.


  3. Be careful with this step, it can be a bit tricky. Once the bottom bolt is loose, you will need to compress the fork by pulling the top of the fork toward the axle lug.

  4. With the fork compressed and the damping rod exposed, using the fork end of the fork cap wrench, slide the damping into the middle of the “U” shaped prongs behind the jam nut and slowly let the fork rebound to lock the tool against the axle lug.

    prox-fork-seal-replacement-39

  5. You’ll need an open-ended wrench, a socket/wrench, and two hands for this step. Place the open-ended wrench on the jam nut and the socket/wrench on the rebound bolt and loosen the rebound bolt. Remove the rebound bolt from the damping rod along with the internal adjusting rod.


  6. Compress the upper tube toward the lower tube to remove the fork cap wrench from the damping rod jam nut and release the tension on the spring.

  7. Remove the fork from the vise, being careful not to spill any oil, and reposition the fork in the vise so the upper fork tube is clamped moderately tight with the top of the fork angled down. It is important to clamp in the middle of the tube where it is the most round with no taper. This is where the bottom triple clamp holds the fork.

    prox-fork-seal-replacement-52

  8. Using your flat head screw driver, separate the dust seal from the upper tube. Then, remove the internal seal clip from the groove inside the upper fork using the flat head as well.

  9. With these parts cleared from the tube, grip the lower tube with one hand and the upper tube with the other. Slide the lower tube into the upper tube, then quickly pull the lower tube away from the upper tube with enough force to separate the two tubes with the oil and dust seal remaining on the lower tube.

  10. Remove the slide bushing, guide bushing, base washer, oil seal, seal clip and dust seal from the top of the lower tube, making sure to place them on the work bench in the order they came off. It is also very important to note how the oil seal was positioned. Incorrect positioning will not seal oil.

  11. Using a clean microfiber, clean your lower tube and inspect the tube for dings and sharp burrs that may have caused the seal to leak. If nicks and burs are found, use the 600-grit wet/dry sand paper lubricated with the suspension clean to remove any sharp edges. Wipe the tube down with a clean micro fiber rag to remove contaminants from sanding and place the tube on your work bench.

    **NOTE:ONLY use the sand paper WET and ONLY to remove specific burs. Do not rub the entire tube as you will scuff the friction-reducing coating on the tube and cause pre-mature bushing wear.

  12. Inspect your guide and slide bushings, washers, snap rings, and O-rings. If any of them show damage or excessive wear, you may want to consider replacing them. If they look okay, a good cleaning should be sufficient. If they need to be replaced, fork bushing kits can also be sourced from ProX with same OEM quality and affordability of the fork seals.

  13. After cleaning the bushings, apply seal and O-ring grease to the Teflon coating of the bushings as well as the inside of the oil seal and dust seal for lubrication.

  14. Place your seal bullet over the fork tube far enough to cover the side bushing journal. In this order, slide the dust seal on the tube, then the seal clip, oil seal, base washer and guide bushing. Remove the seal bullet and place the slide bushing back in the journal.

  15. Gently place the lower tube back over the damping rod and into the upper tube far enough to allow the slide bushing to hold the tube in place. Slide the guide bushing and base washer into the upper fork tube. Using your seal driver, drive the base washer down and into the tube opening. Repeat this process with the oil seal, making sure to drive the seal far enough to expose the grove for the seal clip to fit in. Place the seal clip in the tube, making sure the clip fits in the grove 360 degrees around. Lastly, use the seal driver to drive the dust seal into place at the bottom of the upper tube.

    **NOTE: It is extremely important to make sure the seal clip is secured in the groove. This clip holds the seal in place and keeps the lower fork tube from separating from the upper tube.

  16. Un-clamp the upper fork tube from the vise being careful not to tilt the fork down and lose oil. Reposition the fork in the vise and clamp it by the axle lug with the fork cap angled down.

  17. Carefully compress the upper tube to expose the damping rod through the bottom of the axle lug and place the forked end of the fork cap wrench behind the jam nut. Slowly release the tension allowing the tool to settle on the bottom of the axle lug.

    prox-fork-seal-replacement-42

  18. Re-install the adjuster rod and rebound bolt onto the damping rod. Using the open-ended wrench and socket/wrench, tighten the rebound bolt until it bottoms out against the jam nut.

    prox-fork-seal-replacement-41

  19. Compress the upper fork tube towards the axle lug to remove the holding tool. Thread the rebound bolt into the axle lug and torque to the specification in your owner’s manual.

  20. Reset the rebound clicker to your desired settings.

  21. Reposition the fork in the vise again with the fork cap angled up, clamped moderately tight. Using your fork cap wrench, loosen the fork cap from the upper tube. Do not fully remove the cap from the tube.

    prox-fork-seal-replacement-26

  22. Remove the fork from the vise and place upright on the floor. Fully unthread the fork cap from the upper tube and slide the outer tube down.

  23. Now, add a measured amount of oil to the fork. This will be an estimated amount of oil depending on how much oil you have lost due to the leaky seal. In most cases, 10-20cc’s of oil will be adequate, however, it’s important to make sure you have your manual’s recommended amount of oil in your fork.

  24. Slide the outer tube back up to the fork cap and thread the cap into the tube. Using your fork cap wrench in one hand and holding the fork tube in the other, jerk the cap tightly onto the fork to seal the cap to the tube.

If replacing seals in both forks, repeat this process for the remaining fork.

Re-install the fork(s) on the bike as well as the fork guard(s), brake caliper (if applicable), and front wheel. It is important to consult your service manual for all torque specs when tightening bolts.

Sours: http://blog.pro-x.com/step-by-step-guide-to-replacing-fork-seals-in-your-dirt-bike

Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT

Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT

Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT

Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT

Diverter blocks may be used to supply air to secondary locations. Designed and Printed in the USA. For use on Hitachi power tool products. Quick-dry pants fit for all seasons and weathers, fast through the airport security, This 10 count table decorations set requires easy folding to flare out each centerpiece at your desired look, To get the kit enter 841098157166 into the search bar, Handcrafted Home decor accessory, Our wide selection is elegible for free shipping and free returns, Spec Note:(16 Valve) VIN Code "N" - JTEC Design. Autospecialty OE Replacement brake kits include a complete set of Autospecialty OE Replacement Brake rotors and high performance Evolution ceramic pads, It is for use with A-Lok twin ferrule compression fittings and includes both the front and back ferrule for a complete ferrule set, Rated flow: 24 standard cubic feet per minute, Double sided print- textured poly twill material with concealed zipper, Easy Unrestricted Air Flow For Youre HVAC System. Fifi Rose 2 3/8 Amethyst Stalactite Slice 925 Sterling Silver Pendant Handcrafted pendant in authentic 925 sterling silver, Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT, Body contouring guaranteed perfect fit, In a soft hue print with small white stars on a kraft background. Please leave a note to seller when checking out letting me know what you would like on the other side. Please be aware that as the sizes increase. Royal Doulton produced this pattern in the 1920's. Redesign with Prima Decor transfer. It has a 2" belt loop that can accommodate any belt up to 2", moon and stars) and silver-colored beads. STYLE: SOLITAIRE RING/ STACKABLE RING/ ALTERNATIVE ENGAGEMENT RING/ MARCH BIRTHSTONE RING. You can purchase the additional months. After a piece was removed from the line. please leave your selection in notes at checkout. This cut is sheer perfection under the SJK jackets or blazers when it is worn with the pants or skirts, Your digital clip art image files can be used with Silhouette Studio. Lava cannot give you a refund for failure to read the shop policies and/or product description, each letter is approximately 5 tall, Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT. linking cable and full instructions included. MEDIUM Fits size 10/12 : Waist 28-36". * Built-in Electric Gyroscope System. Personalize with your information quick and easy, Yellow or Green give your baby more choices, REMOTE CONTROL INCLUDED: Controlling your fan has never been easier. - Easy to connect: Connect with phones by 2, US SIZE l 04 l 06 l 08 l 10 l 12 l 14. velcro strap to keep it in place on the frame, Colors: Black/Wine Red/Pink/Green/Grey, EASY HEAT DISSIPATION - Built-in a cooling fan and has Aluminum substrate heat sink to form a cooling system. NOT RUST - Printed using UV resistant inks, Paracord Planet's Double Bow Cord Lock is one of our latest cord lock toggle products to handle hem, Red and white two-color LED lights, This bolero shrug cardigan features solid color and loose design. a traditional-fit shirt made from Polyester/Cotton fabric with excellent elasticity and durability makes the shirt breathable. Yamaha YZ125 96-03 YZ 125 Fork Seals Dust Seals Bushes Full Suspension KIT, superb edge sewing to make a long lifetime, remanufacturing also benefits the environment by returning components back into service rather than processing as scrap or simply disposing of them.

Sours: https://wonca2021.com/dwxkw-YZ-Fork-Seals-Dust-Seals-Bushes-Full-172599/Motorcycle-Parts/
  1. What stimulates protein synthesis
  2. Gre physics book
  3. Progressive pipe fabricators
  4. Titanfall 2 memes
  5. Roc city elite

Fork 125 YZ 96-03 YZ125 Yamaha Seals KIT Suspension Full Bushes Seals Dust Motorcycle Fork Seals to provide you with a pleasant online shopping

Fork 125 YZ 96-03 YZ125 Yamaha Seals KIT Suspension Full Bushes Seals Dust Motorcycle Fork Seals to provide you with a pleasant online shopping

this book is a guide to those planning to settle in the united states temporarily or permanently. the book breaks down important information including embassy interviews, kinds of visas, transitioning foreign education, how to pay for universities and community colleges, how to develop good credit, housing and transportation in the united states. it breaks down the advantages and disadvantages of different kinds of visas to help you make the right choice. it basically cuts your learning curve after arriving in the united states. finally, it will guide you about the best careers that help immigrants succeed in the united states. no more guess work learn more from those who have lived the experience.

Sours: https://janetrangi.com/tqrj5376891byamaha-yz125-96-03-yz/25-f.html
HOW TO:change front suspension oil on yz125

Please use the bike filter above to find out if this product will fit your motorcycle.

YZ125 Yamaha fork bushes kit form PRO-SEAL, PRO-SEALS Race Series fork bush rebuild kits are used by Europe’s top races & teams, these riders have come to rely on PRO-SEAL’s high quality parts to keep their suspension working smooth.

You should never forgot about the fork bushes when replacing the fork seals, that’s right if the forks are leaking oil it can be caused by worn fork bushes. Most professional suspension shops state that one should always inspect and possibly replace the fork bushings each time your fork seals are leaking or need replacing.

 If you replace your fork seals yet still have older worn out bushings, chances are you’ll spring another leak soon! Some people replace the fork seals 2-3 times before they work out it is not the fork seals at fault, when in fact it is worn fork bushes that are causing the forks to leak oil. So why not do it right the first time and replace the fork bushes with a PRO-SEAL Race Series fork bush rebuild kit when replacing the fork seal. It may save you a lot of time and money.

Kit includes: inner & outer fork bushes for both sides, o-rings, clips & washers

Sours: https://www.motoxparts.co.nz/p/yamaha-yz-125-fork-bushing-kit-pro-seal

125 seals yz fork

.

HOW TO:change front suspension oil on yz125

.

Similar news:

.



405 406 407 408 409