Ender 3 display

Ender 3 display DEFAULT

How to fix the Ender 3 blue screen of death

If your Ender 3 Pro displays a blank screen when you switch it on, you may worry that you have a faulty printer.

Luckily, if you bought your Ender recently, it&#;s probably not that bad.

Maybe you accidentally flashed the firmware

I had a blank screen on my Ender 3 Pro. I eventually figured out that I had removed the firmware without realising.

If something goes wrong with the firmware, the printer know how to tell you what has happened. The main fan spins up as normal, and the screen turns on, but it&#;s blank.

In my case, I had already gotten a few successful prints out of the machine so I knew I hadn&#;t set anything up backwards. I checked that all of the cables were still plugged in. Everything felt fine.

How to temporarily brick your Ender 3

In the moments before I semi-bricked my Ender, I had a couple of micro SD cards out on the desk.

I picked up the wrong card, put it into the Ender 3 to load my next print, and switched it on. Blank screen.

I switched it on and off a couple of times.

Still blank.

What I figured out later was that I had just booted up the Ender with the wrong SD card in it. It happened to be one I had previously loaded with Octopi.

The printer powered up, found something on the SD that it thought was new firmware, and swapped it in.

Since I had no idea what was going on with this blue screen, I took to Google and binged on some obscure threads.

I was hoping I hadn&#;t inadvertently fried some component. Had I moved the tray too quickly and caused a voltage spike? How delicate are these things?

I kept digging through forum threads until I got to the bottom of it.

At first, I hadn&#;t considered that I&#;d flashed the firmware. I was under the impression that you needed an arduino and a bunch of cables to do that.

However, since the arrival of the Ender V-2, the Ender 3 and Ender 3 Pro models have started shipping with a new, bit motherboard.

These newer motherboards can flash their firmware via SD, and this is something the original Ender 3 could not do. With the older models, you&#;ve have to break out the arduino and a couple of jumper wires.

This automatic flash feature must be very handy in the factory, but it could use a sticker or something. Every day, all over the world, people are switching their printers on and off to get the blue screen to go away.

It doesn&#;t go away.

Until now.

Easy fix for the blue screen of death

The fix is easy.

Simply download the Ender 3 Pro firmware, put this .bin file onto the root level of an SD card.

Power off your Ender 3, insert this SD card, and then power it back up.

The screen will remain blank for a few seconds but then will boot up as normal.

The firmware that worked for me was the:

which I found here.

That&#;s it.

Your printer should be back to normal, assuming you had the same problem as I did.

Perhaps something much more terrible has happened. This approach is unlikely to work for fire-damaged, submerged or crushed printers.

I hope that helped

It took some Googling to figure this out, so I thought I&#;d write it up and save someone some time. Let me know how you get on. If you&#;d like, you could even buy me a coffee.

Happy printing.

Like this:

LikeLoading

Sours: https://focalise.ie/fix-enderpro-blank-screen/
  • Download: free
    Website: Thingiverse

     Tags  Pivoting Display for Ender 3 - Pro - V2 - Ender

     Text btt, btt tft, btt tft35, creality, creality ender 3, display, display mount, ender, ender 3 v2, ender 5, ender3, ender 3, ender 3 pro, lcd display, boothyboothy,

  • Download: free
    Website: Cults

     Tags  STL file Pivoting Display for Ender 3 - Pro - V

     Text btt, btt tft, btt tft35, creality, creality ender 3, display, display mount, ender, ender 3 v2, ender 5, ender3, ender 3, ender 3 pro, lcd display, 3d printer parts,

  • Download: free
    Website: Thingiverse

     Tags  Slim Pivoting Display Housing for the Ender 3 &am

     Text bigtreetech, bigtreetech tft35, bigtreetech tft35 v3, btt, btt tft, btt tft35, creality ender 3, display, display case, display mount, ender, ender 5, ender3, ender 3, ender 3 pro, boothyboothy,

  • Download: free
    Website: Cults

     Tags  STL file Slim Pivoting Display Housing for the En

     Text bigtreetech, bigtreetech tft35, bigtreetech tft35 v3, btt, btt tft, btt tft35, creality ender 3, display, display case, display mount, ender, ender 5, ender3, ender 3, ender 3 pro, 3d printer parts,

  • Download: free
    Website: Thingiverse

     Tags  slim display mount (ender 3 v2)

     Text creality ender 3, display, display mount, ender3, ender3 v2, ender 3, ender 3 accessories, ender 3 display, ender 3 upgrade, ender 3 v2 mods, ender 3 v2 screen, ender 3 v2 upgrades, lcd, lcd display, lcd holder, lcd mount, mount, safe space, slim, slimmer, smaller, smaller printer, tiny, tiny printer, upgrade,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 v2 display backplate Ender 3v2

     Text backplate, cover, creality ender 3, display, ender 3v2, ender 3 v2, lcd, lcd display, lcd screen, mount, screen, tft display, tft screen, ci3jk4 fpv,

  • Download: free
    Website: Thingiverse

     Tags  Ender-3 LCD Display Stand

     Text beeper silencer, cover, creality, display case, display mount, display stand, ender, ender3, ender 3, ender 3 cover, frame, lcd, stand alone,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 Display and Electronic Stand for SKR

     Text bigtreetech skr, creality, display, display mount, display stand, electronics, electronics enclosure, enclosure, ender, ender 3, ender 3 pro, skr, skr 13,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 Control box with 2x buck converter and dr

     Text buck converter, controlbox, controlbox ender3, creality, creality ender 3, display, ender, ender 3, bjornweytjens,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 Display Stand

     Text , cr, creality, creality cr, creality ender 3, display, display case, display mount, display stand, emder3, ender, ender 3 pro, lcd, lcd, lcd , lcd holder, lcd case, lcd display, lcd holder, lcd mount, stand,

  • Download: free
    Website: Thingiverse

     Tags  (Ender 3) Ikea Lack - Display mount + Thermistor

     Text 3d printer enclosure, creality, creality cr, creality ender 3, display, enclosure, ender, ender 3, ikea, ikea lack, lcd, lcd case, lcd mount, screen,

  • Download: free
    Website: Cults

     Tags  (Ender 3) Ikea Lack - Display mount + Thermistor

     Text 3d printer enclosure, creality, creality cr, creality ender 3, display, enclosure, ender, ender 3, ikea, ikea lack, lcd, lcd case, lcd mount, screen, 3d printer parts,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 Screen Left side

     Text , creality ender 3, display, display mount, display stand, ender, ender3, ender 3, ender 3 pro, ender 3 v2, lcd, lcd, lcd holder, lcd mount, lcd screen, screen holder, screen mount,

  • Download: free
    Website: Thingiverse

     Tags  Tablet Mount for the Creality Ender 3

     Text android, arduino, creality, creality ender 3, display, ender3, ender3pro, ender 3, monitor, octopi, octoprint, raspberry pi, tablet,

  • Download: free
    Website: Cults

     Tags  STL files Tablet Mount for the Creality Ender 3 ・

     Text android, arduino, creality, creality ender 3, display, ender3, ender3pro, ender 3, monitor, octopi, octoprint, raspberry pi, tablet, 3d printer accessories,

  • Download: free
    Website: Thingiverse

     Tags  ender 3 display case standalone

     Text case, creality, creality ender 3, display, display case, display stand, ender 3 pro, lcd display, lcd holder, lcd mount, stand, standalone,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3, left support for RepRapDiscount Full Gra

     Text creality, creality ender 3, display, ender 3, reprap, reprapdiscount, reprap discount, smart lcd controller, support, upgrade,

  • Sours: https://www.yeggi.com/q/ender+3+display/
    1. Barrage rc
    2. Sugar gliders austin
    3. Pfaltzgraff made in china
    Ender 3 touchscreen final photo

    As is the norm, here's a completed photo of the Ender 3 touch screen setup.

    Ender 3 touchscreen 3D model

    The best model I found for the " Adafruit touchscreen I'll be using is by designer Tronnic. It mounts to the lower-left aluminum extrusion on the Ender 3, resulting in a symmetrical addition that looks like it came from the factory.

    Download the model from Thingiverse and print the following:

    QTYFile
    10_Ender3_Touchscreen_Holder_Base.stl
    11_2_Ender3_Touchscreen_Pi_Case_no_letters.stl
    12_1_Ender3_Touchscreen_Pi_Back_40mm_Fan.stl or 2_Ender3_Touchscreen_Pi_Back.stl*
    23_1_Ender3_Touchscreen_Pi_Clamp.stl
    15_Ender3_Touchscreen_Support.stl
    16_Ender3_Camera_Bracket

    * If you decide to add a fan to your enclosure, I recommend printing the 40mm fan back. Otherwise, print the blank back.

    Raspberry Pi 4

    If you're using the Raspberry Pi 4 for OctoPrint, be sure to print this remix as well.

    Print settings

    For the main holder base/bracket, I recommend printing at least 50% infill. If you're using Cura, I recommend the "Gyroid" infill pattern. I printed with 15% "Cubic" infill originally, and the weight from the Pi and fan caused slight sagging.

    If you like perfect symmetry, I recommend you also print this separate screen surround to border the original Ender 3 screen.

    You can print all the files without supports by orienting them correctly.

    Touchscreen HAT mounted to a Raspberry Pi

    I wrote a separate, full guide on adding an OctoPrint touchscreen to any 3D printer. Use that guide to configure the screen to work with OctoPrint, then return here for Ender 3-specific instructions!

    I also made an OctoPrint touchscreen video in case you prefer to learn that way:

    Attaching a Raspberry Pi camera ribbon cable

    Attach your camera ribbon cable to the Raspberry Pi, routing it above the HDMI connector.

    Don't bend the cable too much or you may damage it!

    Connecting the touchscreen to the pi

    The "support" model you printed is used in place of standoffs. Insert it between your screen and the Raspberry Pi and slide the screen onto the Pi's GPIO header.

    If your screen came with standoffs and they're about the same size as the support model, I recommend using those instead.

    Inserting the case into the main frame

    Slide the case into the main frame that will connect to the Printer. Orient it so that the "thicker" part of the frame is to the left.

    Be careful! The case is VERY thin and easy to break. Once everything is assembled, it's quite sturdy.

    Connecting the Pi to the case

    Insert the Pi into the case and ensure there's a snug fit.

    If your touchscreen came with 4 small perforated tabs on the corner, you may need to snap them off with a pair of pliers to make the screen fit in your case—I already did this before taking this photo.

    Be careful—the case is super thin and easy to break. Once it's assembled it's much sturdier.

    Ender 3 Raspberry Pi fan

    Using this 40mm USB fan is optional but recommended. It's only $10, so I decided to do it just to ensure I always get the highest quality prints possible. Using the included screws, mount the fan so that it sucks air away from the Pi (blowing out the back). Cover the screws with Kapton tape to prevent shorts.

    If you're handy with a soldering iron, I recommend shortening the USB cable to make things neater.

    Securing the backplate

    Secure the fan or non-fan backplate using the two clamps you printed. If you aren't using a fan, use the blank backplate instead.

    Be careful not to snap the edges off of your case when you connect them! The case is thin.

    Mounting the touchscreen assembly to the Ender 3

    Remove the two screws from the lower left part of your printer and use them to secure the new touchscreen housing.

    Ender 3 touchscreen camera mount

    The old camera mount that most Ender 3 owners use will block the touchscreen. Tronnic was awesome enough to remix that original camera mount into one that won't block the screen.

    Swap the old mount out for the new one.

    Reconnecting power and data cables

    Reconnect your power and data cables to the Pi. If you're powering your Pi from your 3D printer, you'll probably need to solder a longer Micro USB cable to your buck converter or run a micro USB extension cable such as this one.

    Make sure the power cable routers downward and doesn't obstruct the Z-axis limit switch!

    Ender 3 screen surround

    If you printed the optional screen surround for the original screen, mount it around the original Ender 3 using a bit of hot glue or foam tape. This makes things look a bit nicer and adds additional symmetry!

    Ender 3 OctoPrint touchscreen close-up shot

    Your Ender 3 now has an awesome touchscreen that you can use to control your printer.

    Next,update your Ender 3 firmware. Many Ender 3s shipped with unsafe, outdated firmware that lacks thermal runaway protection; thermal runaway is a leading cause of 3D printer fires. Updating your firmware only takes a few minutes and is an important safety upgrade!

    Sours: https://howchoo.com/ender3/enderoctoprint-touchscreen
    Creality ENDER 3 Touch Screen Upgrade

    Creality Ender 3 Display Cables

    Original replacement cable for the Creality 3D Ender 3 screen

    • Original spare part
    • From Creality 3D
    • For Ender 3 and Ender 3 Pro
    • Creality Ender 3 Display Cables - 1 pc

    Price shown includes 20% VAT.Excludes delivery costs

    Only 3 items in stock

    Delivery on Wednesday, 20 October: Order before Monday at

    • Original spare part
    • From Creality 3D
    • For Ender 3 and Ender 3 Pro

    Product information & technical details

    Item no.:CRE
    Manufacturer No.:
    Manufacturers:Creality
    Content:1 pc

    Description

    This is an original display cable for Creality Ender 3 and Ender 3 Pro.

    Questions & Answers about Creality Ender 3 Display Cables

    Pose a question about this product to customers who have already purchased the item. Please forward any other order-related questions to our Customer Service Team.

    • What’s the product length?

      1 Answer, last answered on 29 September

      • Andrew

        29 September

        Customer Service

    Customer Reviews

    Did you know?

    The concept of the 3D printer came about from an American inventor and engineer, Chuck Hull, during the s80s. He also founded the company called 3D Systems.

    Sours: https://www.3djake.com/creality-3d-printers-spare-parts/enderdisplay-cables

    Display ender 3

    Upgraded Touch Panel Screen Display for Ender-3 (Pro) /Ender 3 V2

    Before use:

    Please flash your mainboard with the correct firmware after installed the touch screen.

     

     

     

    ✔Super easy to install the touchscreen, quick setup, and easier to use.

    ✔Inch HD color screen & bit color HD screen displays clear views.

    ✔An innovative UI interface brings you an incredibly interactive experience, totally different from the standard knob screen.

    ✔The touch panel screen display only compatible with bit mainboard( or )

    ✔Compatible with Creality Ender 3 Pro ,Ender 3, Ender 3 v2, Ender 3X.

     

    Ender touch screen Creality 3D Printer

    9 Languages

    English, Chinese, Japanese, Spanish, Korean, French, Russian, German, Arabic, 9 languages can be switched freely to enhance user control experience.

    Ender touch screen Creality 3D Printer

    Mass Memory

    It provides sufficient storage space and supports storing pictures in JPEG compression mode, further increasing the number of stored files.

    Ender touch screen Creality 3D Printer

    Easy to Installation

    The screen is tilted to make a wide vision and easy to operate. It can be fixed directly on the 3D Printer base.

    Sours: https://www.creality3dofficial.com/products/upgraded-touch-panel-screen-display-for-enderpro-enderv2
    Ender 3/3pro upgrade to v2??!!
  • Download: free
    Website: Thingiverse

     Tags  Ender 3 lcd side mount

     Text creality ender 3, ender, ender 3 lcd, ender lcd, ender3, ender 3, ender 3 accessories, ender 3 mods, ender 3 upgrade, lcd, lcd display, lcd ender3, lcd holder, lcd mount,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 LCD Right Angle & Relocation

     Text creality ender 3, ender, ender 3, ender 3x, ender 3 lcd cover, ender lcd, lcd, lcd cover, move, relocate, mr spiffy,

  • Download: free
    Website: Thingiverse

     Tags  Creality Ender-3 station (LCD + Raspberry Pi)

     Text box, case, creality ender 3, ender, ender3, ender 3, lcd case, octopi, octopi mount, octoprint, raspberry pi, raspberry pi 3, raspberry pi camera, raspberry pi case, station,

  • Download: free
    Website: Thingiverse

     Tags  Bracket / holder for Ender 3 LCD control box + La

     Text bracket, control box, controlbox, creality ender 3, ender 3, ikea, ikea lack, lack, lcd holder, lcd mount, freich,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 LCD Cover

     Text cover, creality, creality ender 3, ender 3, ender 3 lcd cover, lcd, lcd cover, phelps3d, ender 3 lcd cover by, phelps3d,

  • Download: free
    Website: Thingiverse

     Tags  Ender-3 LCD wire cover

     Text cover, creality ender 3, ender, ender-3 pro, ender3, ender 3, lcd, wire cover, wire molding, jrpsoul,

  • Download: free
    Website: Thingiverse

     Tags  MKS LCD A/B

     Text , case, ender 3, lcd, lcd, lcdab, lcd box, lcd , lcd holder, lcd case, lcd display, lcd holder, lcd mount, mks, mks lcd, mount ,

  • Download: free
    Website: Thingiverse

     Tags  Creality3D Ender 3 LCD case

     Text box, case, creality, creality3d, display, electronics enclosure, enclosure, ender, ender 3, external, external hard drive, lcd, pcb, protector, screen,

  • Download: free
    Website: Thingiverse

     Tags  LCD Mounting Bracket (Used for: No Frame Guide Re

     Text cr, cr portable, cr10, cr10 lcd mount, cr10 portable, cr10s, cr10s lcd mount, cr10s standalone, cr10s4, cr10s5, cr10spro, creality, creality cr, creality crs, creality ender 2, creality ender 3, lcd bracket, lcd mount, mount, mounting bracket, lcd mounting bracket by, jueda,

  • Download: free
    Website: Cults

     Tags  STL file Ender 3 LCD Cover • 3D printable model ・

     Text cover, creality, creality ender 3, ender 3, ender 3 lcd cover, lcd, lcd cover, phelps3d, 3d printer accessories,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 LCD Beeper Cap

     Text 3d printer, beeper, cap, ender, ender 3, hat, lcd, loud, printer, silencer, scuddy,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 LCD Cover with SD Card Shelf

     Text back, cover, creality, creality ender 3, ender 3, kash, lcd, lcd case, micro sd card holder, sd card holder, kash,

  • Download: free
    Website: Cults

     Tags  Display cases for Ender 3 and BIGTREETECH TFT35 V

     Text bigtreetech skr, creality ender 3, ender3, ender 3, lcd case, marlin, marlin 2, marlin firmware, 3d printer parts,

  • Download: free
    Website: Cults

     Tags  Ender 3 LCD Bracket • Object to 3D print ・

     Text corner bracket, creality ender 3, ender, ender 3, ender 3 pro, lcd bracket, lcd mount, mounting bracket, 3d printer parts,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3/cr10/ 7 inch Touch Screen LCD

     Text creality ender 3, ender3, ender 3, lcd case, lcd mount, octoprint, raspberry pi, raspberry pi screen, screen, touchscreen, touchui,

  • Download: free
    Website: Thingiverse

     Tags  Ender-3 LCD Rear Cover

     Text display rear cover, display cover, ender-3, ender3, ender 3, lcd rear cover, lcd cover, qurvento, gnu - gpl,

  • Download: free
    Website: Thingiverse

     Tags  Ender 3 v2 screen cover

     Text cover, creality ender 3, ender3, ender3v2, ender 3, lcd cover, lcd guard, lcd lid, lcd protection, led cover, lid, upgrade ender 3 v2,

  • Sours: https://www.yeggi.com/q/ender+3+lcd/

    You will also like:

    .



    464 465 466 467 468